Certain Cold-Rolled Steel Flat Products

The products covered by this order are certain cold-rolled (cold-reduced), flat-rolled steel products, whether or not annealed, painted, varnished, or coated with plastics or other non-metallic substances. The products covered do not include those that are clad, plated, or coated with metal. The products covered include coils that have a width or other lateral measurement ("width") of 12.7 mm or greater, regardless of form of coil (e.g., in successively superimposed layers, spirally oscillating, etc.). The products covered also include products not in coils (e.g., in straight lengths) of a thickness less than 4.75 mm and a width that is 12.7 mm or greater and that measures at least 10 times the thickness. The products covered also include products not in coils (e.g., in straight lengths) of a thickness of 4.75 mm or more and a width exceeding 150 mm and measuring at least twice the thickness. The products described above may be rectangular, square, circular, or other shape and include products of either rectangular or non-rectangular cross-section where such cross-section is achieved subsequent to the rolling process, i.e., products which have been "worked after rolling" (e.g., products which have been beveled or rounded at the edges). For purposes of the width and thickness requirements referenced above: (1) Where the nominal and actual measurements vary, a product is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above, and (2) where the width and thickness vary for a specific product (e.g., the thickness of certain products with non-rectangular cross-section, the width of certain products with non-rectangular shape, etc.), the measurement at its greatest width or thickness applies. Steel products included in the scope of this order are products in which: (1) Iron predominates, by weight, over each of the other contained elements; (2) the carbon content is 2 percent or less, by weight; and (3) none of the elements listed below exceeds the quantity, by weight, respectively indicated: 2.50 percent of manganese, or 3.30 percent of silicon, or 1.50 percent of copper, or 1.50 percent of aluminum, or 1.25 percent of chromium, or 0.30 percent of cobalt, or 0.40 percent of lead, or 2.00 percent of nickel, or 0.30 percent of tungsten (also called wolfram), or 0.80 percent of molybdenum, or 0.10 percent of niobium (also called columbium), or 0.30 percent of vanadium, or 0.30 percent of zirconium. Unless specifically excluded, products are included in this scope regardless of levels of boron and titanium. For example, specifically included in this scope are vacuum degassed, fully stabilized (commonly referred to as interstitial-free (IF)) steels, high strength low alloy (HSLA) steels, motor lamination steels, Advanced High Strength Steels (AHSS), and Ultra High Strength Steels (UHSS). IF steels are recognized as low carbon steels with micro-alloying levels of elements such as titanium and/or niobium added to stabilize carbon and nitrogen elements. HSLA steels are recognized as steels with micro-alloying levels of elements such as chromium, copper, niobium, titanium, vanadium, and molybdenum. Motor lamination steels contain micro-alloying levels of elements such as silicon and aluminum. AHSS and UHSS are considered high tensile strength and high elongation steels, although AHSS and UHSS are covered whether or not they are high tensile strength or high elongation steels. Subject merchandise includes cold-rolled steel that has been further processed in a third country, including but not limited to annealing, tempering, painting, varnishing, trimming, cutting, punching, and/or slitting, or any other processing that would not otherwise remove the merchandise from the scope of the order if performed in the country of manufacture of the cold-rolled steel. All products that meet the written physical description, and in which the chemistry quantities do not exceed any one of the noted element levels listed above, are within the scope of this order unless specifically excluded. The following products are outside of and/or specifically excluded from the scope of this order: Ball bearing steels; Tool steels; Silico-manganese steel; Grain-oriented electrical steels (GOES) as defined in the final determination of the U.S. Department of Commerce in Grain-Oriented Electrical Steel From Germany, Japan, and Poland; Non-Oriented Electrical Steels (NOES), as defined in the antidumping orders issued by the U.S. Department of Commerce in Non-Oriented Electrical Steel From the People's Republic of China, Germany, Japan, the Republic of Korea, Sweden, and Taiwan. Also excluded from the scope of this order is ultra-tempered automotive steel, which is hardened, tempered, surface polished, and meets the following specifications: Thickness: less than or equal to 1.0 mm; Width: less than or equal to 330 mm; Chemical composition with specified element ranges; Physical properties with flatness requirements; Microstructure specifications; Surface roughness specifications; Non-metallic inclusion limits; and Mill test certificate requirements.