Fujian Yinfeng Imp & Exp Trading Co., Ltd

The merchandise subject to this order consists of wood mouldings and millwork products that are made of wood (regardless of wood species), bamboo, laminated veneer lumber (LVL), or of wood and composite materials (where the composite materials make up less than 50 percent of the total merchandise), and which are continuously shaped wood or finger-jointed or edge-glued moulding or millwork blanks (whether or not resawn). The merchandise subject to this order can be continuously shaped along any of its edges, ends, or faces. The percentage of composite materials contained in a wood moulding or millwork product is measured by length, except when the composite material is a coating or cladding. Wood mouldings and millwork products that are coated or clad, even along their entire length, with a composite material, but that are otherwise comprised of wood, LVL, or wood and composite materials (where the non-coating composite materials make up 50 percent or less of the total merchandise) are covered by the scope. The merchandise subject to this order consists of wood, LVL, bamboo, or a combination of wood and composite materials that is continuously shaped throughout its length (with the exception of any endwork/dados), profiled wood having a repetitive design in relief, similar milled wood architectural accessories, such as rosettes and plinth blocks, and finger-jointed or edge-glued moulding or millwork blanks (whether or not resawn). The scope includes continuously shaped wood in the forms of dowels, building components such as interior paneling and jamb parts, and door components such as rails, stiles, interior and exterior door frames or jambs (including split, flat, stop applied, single- or double-rabbeted), frame or jamb kits, and packaged door frame trim or casing sets, whether or not the door components are imported as part of a door kit or set. The covered products may be solid wood, laminated, finger-jointed, edge-glued, face-glued, or otherwise joined in the production or remanufacturing process and are covered by the scope whether imported raw, coated (e.g., gesso, polymer, or plastic), primed, painted, stained, wrapped (paper or vinyl overlay), any combination of the aforementioned surface coatings, treated, or which incorporate rot-resistant elements (whether wood or composite). The covered products are covered by the scope whether or not any surface coating(s) or covers obscure the grain, textures, or markings of the wood, whether or not they are ready for use or require final machining (e.g., endwork/dado, hinge/strike machining, weatherstrip or application thereof, mitre) or packaging. All wood mouldings and millwork products are included within the scope even if they are trimmed; cut-to-size; notched; punched; drilled; or have undergone other forms of minor processing. Subject merchandise also includes wood mouldings and millwork products that have been further processed in a third country, including but not limited to trimming, cutting, notching, punching, drilling, coating, or any other processing that would not otherwise remove the merchandise from the scope of this order if performed in the country of manufacture of the in-scope product. Excluded from the scope of this order are countertop/butcherblocks imported as a full countertop/butcherblock panel, exterior fencing, exterior decking and exterior siding products (including solid wood siding, non-wood siding (e.g., composite or cement), and shingles) that are not LVL or finger jointed; finished and unfinished doors; flooring; parts of stair steps (including newel posts, balusters, easing, gooseneck, risers, treads, rail fittings and stair stringers); picture frame components three feet and under in individual lengths; and lumber whether solid, finger-jointed, or edge-glued. To be excluded from the scope, finger-jointed or edge-glued lumber must have a nominal thickness of 1.5 inches or greater and a certification stamp from an American Lumber Standard Committee-certified grading agency. The exclusion for lumber whether solid, finger-jointed, or edge-glued does not apply to screen/''surfaced on 4 sides'' (S4S) and/or ``surface 1 side, 2 edges'' (SlS2E) stock (also called boards) that are finger-jointed and/or edge-glued, or to finger-jointed and/or edge-glued moulding or millwork blanks (whether or not resawn). Accordingly, S4S and S1S2E stock/boards that are not finger-jointed or edge-glued are excluded from the scope of this order. Excluded from the scope of this order are all products covered by the scope of the countervailing duty order on Hardwood Plywood from the People's Republic of China. See Certain Hardwood Plywood Products from the People's Republic of China: Countervailing Duty Order, 83 FR 513 (January 4, 2018). Excluded from the scope of this order are all products covered by the scope of the countervailing duty order on Multilayered Wood Flooring from the People's Republic of China. See Multilayered Wood Flooring from the People's Republic of China: Countervailing Duty Order, 76 FR 76693 (December 8, 2011). Excluded from the scope of this order are all products covered by the scope of the countervailing duty order on Wooden Cabinets and Vanities from the People's Republic of China. See Wooden Cabinets and Vanities and Components Thereof from the People's Republic of China: Countervailing Duty Order, 85 FR 22134 (April 21, 2020).