Non-Selected Companies Under Review

The merchandise covered by these orders is steel racks and parts thereof, assembled, to any extent, or unassembled, including but not limited to, vertical components (e.g., uprights, posts, or columns), horizontal or diagonal components (e.g., arms or beams), braces, frames, locking devices (e.g., end plates and beam connectors), and accessories (including, but not limited to, rails, skid channels, skid rails, drum/coil beds, fork clearance bars, pallet supports, row spacers, and wall ties). Subject steel racks and parts thereof are made of steel, including, but not limited to, cold and/or hot-formed steel, regardless of the type of steel used to produce the components and may, or may not, include locking tabs, slots, or bolted, clamped, or welded connections. Subject steel racks have the following physical characteristics: (1) Each steel vertical and horizontal load bearing member (e.g., arms, beams, posts, and columns) is composed of steel that is at least 0.044 inches thick; (2) Each steel vertical and horizontal load bearing member (e.g., arms, beams, posts, and columns) is composed of steel that has a yield strength equal to or greater than 36,000 pounds per square inch; (3) The width of each steel vertical load bearing member (e.g., posts and columns) exceeds two inches; and (4) The overall depth of each steel roll-formed horizontal load bearing member (e.g., beams) exceeds two inches. In the case of steel horizontal load bearing members other than roll-formed (e.g., structural beams, Z-beams, or cantilever arms), only the criteria in subparagraphs (1) and (2) apply to these horizontal load bearing members. The depth limitation in subparagraph (4) does not apply to steel horizontal load bearing members that are not roll-formed. Steel rack components can be assembled into structures of various dimensions and configurations by welding, bolting, clipping, or with the use of devices such as clips, end plates, and beam connectors, including, but not limited to the following configurations: (1) Racks with upright frames perpendicular to the aisles that are independently adjustable, with positive-locking beams parallel to the aisle spanning the upright frames with braces; and (2) cantilever racks with vertical components parallel to the aisle and cantilever beams or arms connected to the vertical components perpendicular to the aisle. Steel racks may be referred to as pallet racks, storage racks, stacker racks, retail racks, pick modules, selective racks, or cantilever racks and may incorporate moving components and be referred to as pallet-flow racks, carton-flow racks, push-back racks, movable-shelf racks, drive-in racks, and drive-through racks. While steel racks may be made to ANSI MH16.l or ANSI MH16.3 standards, all steel racks and parts thereof meeting the description set out herein are covered by the scope of these orders, whether or not produced according to a particular standard. The scope includes all steel racks and parts thereof meeting the description above, regardless of (1) other dimensions, weight, or load rating; (2) vertical components or frame type (including structural, roll-form, or other); (3) horizontal support or beam/brace type (including but not limited to structural, roll-form, slotted, unslotted, Z-beam, C-beam, L-beam, step beam, and cantilever beam); (4) number of supports; (5) number of levels; (6) surface coating, if any (including but not limited to paint, epoxy, powder coating, zinc, or other metallic coatings); (7) rack shape (including but not limited to rectangular, square, corner, and cantilever); (8) the method by which the vertical and horizontal supports connect (including but not limited to locking tabs or slots, bolting, clamping, and welding); and (9) whether or not the steel rack has moving components (including but not limited to rails, wheels, rollers, tracks, channels, carts, and conveyors). Subject merchandise includes merchandise matching the above description that has been finished or packaged in a third country. Finishing includes, but is not limited to, coating, painting, or assembly, including attaching the merchandise to another product, or any other finishing or assembly operation that would not remove the merchandise from the scope of these orders if performed in the country of manufacture of the steel racks and parts thereof. Packaging includes packaging the merchandise with or without another product or any other packaging operation that would not remove the merchandise from the scope of these orders if performed in the country of manufacture of the steel racks and parts thereof. Steel racks and parts thereof are included in the scope of these orders whether or not imported attached to, or included with, other parts or accessories such as wire decking, nuts, and bolts. If steel racks and parts thereof are imported attached to, or included with, such non-subject merchandise, only the steel racks and parts thereof are included in the scope. The scope of these orders does not cover: (1) Decks, i.e., shelving that sits on or fits into the horizontal supports to provide the horizontal storage surface of the steel racks; (2) wire shelving units, i.e., units made from wire that incorporate both a wire deck and wire horizontal supports (taking the place of the horizontal beams and braces) into a single piece with tubular collars that slide over the posts and onto plastic sleeves snapped on the posts to create a finished unit; (3) pins, nuts, bolts, washers, and clips used as connecting devices; and (4) non-steel components. Specifically excluded from the scope of these orders are any products covered by Commerce's existing antidumping and countervailing duty orders on boltless steel shelving units prepackaged for sale from the People's Republic of China. Also excluded from the scope of these orders are bulk-packed parts or components of boltless steel shelving units that were specifically excluded from the scope of the Boltless Steel Shelving Orders because such bulk-packed parts or components do not contain the steel vertical supports (i.e., uprights and posts) and steel horizontal supports (i.e., beams, braces) packaged together for assembly into a completed boltless steel shelving unit. Excluded from the scope of these orders are: (1) Wall-mounted shelving and racks, defined as shelving and racks that suspend all of the load from the wall, and do not stand on, or transfer load to, the floor; (2) ceiling-mounted shelving and racks, defined as shelving and racks that suspend all of the load from the ceiling and do not stand on, or transfer load to, the floor; and (3) wall/ceiling mounted shelving and racks, defined as shelving and racks that suspend the load from the ceiling and the wall and do not stand on, or transfer load to, the floor. The addition of a wall or ceiling bracket or other device to attach otherwise subject merchandise to a wall or ceiling does not meet the terms of this exclusion. Also excluded from the scope of these orders is scaffolding that complies with ANSI/ASSE A10.8--2011--Scaffolding Safety Requirements, CAN/CSA S269.2-M87 (Reaffirmed 2003)--Access Scaffolding for Construction Purposes, and/or Occupational Safety and Health Administration regulations at 29 CFR part 1926 subpart L--Scaffolds. Also excluded from the scope of these orders are tubular racks such as garment racks and drying racks, i.e., racks in which the load bearing vertical and horizontal steel members consist solely of: (1) Round tubes that are no more than two inches in diameter; (2) round rods that are no more than two inches in diameter; (3) other tubular shapes that have both an overall height of no more than two inches and an overall width of no more than two inches; and/or (4) wire. Also excluded from the scope of these orders are portable tier racks. Also excluded from the scope of these orders are accessories that are independently bolted to the floor and not attached to the rack system itself, i.e., column protectors, corner guards, bollards, and end row and end of aisle protectors.