Message body
Full text as published by U.S. Customs and Border Protection
1.
On 07/25/2016, Commerce published in the Federal Register its antidumping duty order and amended final determination on certain corrosion-resistant steel products from Taiwan (81 FR 48390).
This message amends certain instructions pertaining to the final determination in this proceeding.
See, message 6154303, dated 06/02/2016.
2.
The products covered by this order are certain flat-rolled steel products, either clad, plated, or coated with corrosion-resistant metals such as zinc, aluminum, or zinc-, aluminum-, nickel- or iron-based alloys, whether or not corrugated or painted, varnished, laminated, or coated with plastics or other non-metallic substances in addition to the metallic coating.
The products covered include coils that have a width of 12.7 mm or greater, regardless of form of coil (e.g., in successively superimposed layers, spirally oscillating, etc.).
The products covered also include products not in coils (e.g., in straight lengths) of a thickness less than 4.75 mm and a width that is 12.7 mm or greater and that measures at least 10 times the thickness.
The products covered also include products not in coils (e.g., in straight lengths) of a thickness of 4.75 mm or more and a width exceeding 150 mm and measuring at least twice the thickness.
The products described above may be rectangular, square, circular, or other shape and include products of either rectangular or non-rectangular cross-section where such cross-section is achieved subsequent to the rolling process, i.e., products which have been “worked after rolling” (e.g., products which have been beveled or rounded at the edges).
For purposes of the width and thickness requirements referenced above:
(1) where the nominal and actual measurements vary, a product is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above, and
(2) where the width and thickness vary for a specific product (e.g., the thickness of certain products with non-rectangular cross-section, the width of certain products with non-rectangular shape, etc.), the measurement at its greatest width or thickness applies.
Steel products included in the scope of this order are products in which:
(1) iron predominates, by weight, over each of the other contained elements; (2) the carbon content is 2 percent or less, by weight; and (3) none of the elements listed below exceeds the quantity, by weight, respectively indicated:
• 2.50 percent of manganese, or
• 3.30 percent of silicon, or
• 1.50 percent of copper, or
• 1.50 percent of aluminum, or
• 1.25 percent of chromium, or
• 0.30 percent of cobalt, or
• 0.40 percent of lead, or
• 2.00 percent of nickel, or
• 0.30 percent of tungsten (also called wolfram), or
• 0.80 percent of molybdenum, or
• 0.10 percent of niobium (also called columbium), or
• 0.30 percent of vanadium, or
• 0.30 percent of zirconium
Unless specifically excluded, products are included in this scope regardless of levels of boron and titanium.
For example, specifically included in this scope are vacuum degassed, fully stabilized (commonly referred to as interstitial-free (“IF”)) steels and high strength low alloy (“HSLA”) steels.
IF steels are recognized as low carbon steels with micro-alloying levels of elements such as titanium and/or niobium added to stabilize carbon and nitrogen elements.
HSLA steels are recognized as steels with micro-alloying levels of elements such as chromium, copper, niobium, titanium, vanadium, and molybdenum.
Furthermore, this scope also includes Advanced High Strength Steels (“AHSS”) and Ultra High Strength Steels (“UHSS”), both of which are considered high tensile strength and high elongation steels.
Subject merchandise also includes corrosion-resistant steel that has been further processed in a third country, including but not limited to annealing, tempering, painting, varnishing, trimming, cutting, punching and/or slitting or any other processing that would not otherwise remove the merchandise from the scope of the investigation if performed in the country of manufacture of the in-scope corrosion resistant steel.
All products that meet the written physical description, and in which the chemistry quantities do not exceed any one of the noted element levels listed above, are within the scope of this order unless specifically excluded.
The following products are outside of and/or specifically excluded from the scope of this order:
• Flat-rolled steel products either plated or coated with tin, lead, chromium, chromium oxides, both tin and lead (“terne plate”), or both chromium and chromium oxides (“tin free steel”), whether or not painted, varnished or coated with plastics or other non-metallic substances in addition to the metallic coating;
• Clad products in straight lengths of 4.7625 mm or more in composite thickness and of a width which exceeds 150 mm and measures at least twice the thickness; and
• Certain clad stainless flat-rolled products, which are three-layered corrosion-resistant flat-rolled steel products less than 4.75 mm in composite thickness that consist of a flat-rolled steel product clad on both sides with stainless steel in a 20%-60%-20% ratio.
The products subject to the order are currently classified in the Harmonized Tariff Schedule of the United States (“HTSUS”) under item numbers:
7210.30.0030, 7210.30.0060, 7210.41.0000, 7210.49.0030, 7210.49.0091, 7210.49.0095, 7210.61.0000, 7210.69.0000, 7210.70.6030, 7210.70.6060, 7210.70.6090, 7210.90.6000, 7210.90.9000, 7212.20.0000, 7212.30.1030, 7212.30.1090, 7212.30.3000, 7212.30.5000, 7212.40.1000, 7212.40.5000, 7212.50.0000, and 7212.60.0000.
The products subject to the order may also enter under the following HTSUS item numbers:
7210.90.1000, 7215.90.1000, 7215.90.3000, 7215.90.5000, 7217.20.1500, 7217.30.1530, 7217.30.1560, 7217.90.1000, 7217.90.5030, 7217.90.5060, 7217.90.5090, 7225.91.0000, 7225.92.0000, 7225.99.0090, 7226.99.0110, 7226.99.0130, 7226.99.0180, 7228.60.6000, 7228.60.8000, and 7229.90.1000.
The HTSUS subheadings above are provided for convenience and customs purposes only.
The written description of the scope of the order is dispositive.
3.
The U.S. International Trade Commission (ITC) determined that critical circumstances do not exist with respect to subject imports from Taiwan.
As a result of the ITC's negative determination of critical circumstances, Commerce will direct CBP in separate instructions to refund all cash deposits collected on entries of certain corrosion-resistant steel products from Taiwan which were entered, or withdrawn from warehouse, for consumption on or after 03/04/2016 and before 06/02/2016.
The interest provisions of section 778 of the Tariff Act of 1930, as amended, do not apply.
4.
For imports of corrosion-resistant steel products from Taiwan, CBP shall continue to suspend liquidation of entries of subject merchandise entered, or withdrawn from warehouse, for consumption on or after 07/20/2016 (date of publication of the International Trade Commission final determination in the Federal Register).
Effective 07/20/2016, CBP shall require a cash deposit equal to the percentage identified below.
All-Others
Case Number:
A-583-856-000
Cash Deposit Rate:
10.34 %
Producer and/or Exporter:
Prosperity Tieh Enterprise Co., Ltd./Yieh Phui Enterprise Co., Ltd./Synn Industrial Co., Ltd.
Case Number:
A-583-856-001
Cash Deposit Rate:
10.34 %
Note:
Commerce, in its final determination (81 FR 35313), collapsed Prosperity Tieh Enterprise Co., Ltd., Yieh Phui Enterprise Co., Ltd., and Synn Industrial Co., Ltd. and treated these companies as a single entity.
Therefore, the above listed cash deposit rate applies to all three named companies.
5.
If there are any questions by the importing public regarding this message, please contact the Call Center for the Office of AD/CVD Operations, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce at (202) 482-0984.
CBP ports should submit their inquiries through authorized CBP channels only.
(This message was generated by OIII:SSL)
6.
There are no restrictions on the release of this information.
Alexander Amdur