CSMS 5140301·Trade policy·May 20, 2015·View on csms.cbp.gov ↗

Notice of final determination in the antidumping duty investigation of Certain Steel Nails from Malaysia (A-557-816)

Plain-English explanation

CSMS 5140301 is a U.S. Customs and Border Protection (CBP) Cargo Systems Messaging Service bulletin (trade policy), published on May 20, 2015. It carries the official CBP guidance brokers and importers must follow for the topic — "Notice of final determination in the antidumping duty investigation of Certain Steel Nails from Malaysia (A-557-816)". It links to 1 AD/CVD case in Tandom's catalog. CSMS messages are the operational layer between Commerce determinations and at-the-border collections: when Commerce publishes a new rate, scope ruling, or instruction, CBP turns it into a CSMS that ACE/ACS systems and brokers act on.

Linked AD/CVD cases(1)

Cases referenced or affected by this CSMS message

A-557-816

Message body

Full text as published by U.S. Customs and Border Protection

1. On 05/20/2015, Commerce published in the Federal Register (80 FR 28969) its final affirmative determination of sales at less-than-fair-value in the antidumping duty investigation of certain steel nails from Malaysia (A-557-816). 2. The products covered by this investigation are certain steel nails having a nominal shaft length not exceeding 12 inches. (See Footnote 1). Certain steel nails include, but are not limited to, nails made from round wire and nails that are cut from flat-rolled steel. Certain steel nails may be of one piece construction or constructed of two or more pieces. Certain steel nails may be produced from any type of steel, and may have any type of surface finish, head type, shank, point type and shaft diameter. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, including but not limited to electroplating or hot dipping one or more times), phosphate, cement, and paint. Certain steel nails may have one or more surface finishes. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk, and sinker. Shank styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted. Screw-threaded nails subject to this proceeding are driven using direct force and not by turning the nail using a tool that engages with the head. Point styles include, but are not limited to, diamond, needle, chisel and blunt or no point. Certain steel nails may be sold in bulk, or they may be collated in any manner using any material. Excluded from the scope of this investigation are certain steel nails packaged in combination with one or more non-subject articles, if the total number of nails of all types, in aggregate regardless of size, is less than 25. If packaged in combination with one or more non-subject articles, certain steel nails remain subject merchandise if the total number of nails of all types, in aggregate regardless of size, is equal to or greater than 25, unless otherwise excluded based on the other exclusions below. Also excluded from the scope are certain steel nails with a nominal shaft length of one inch or less that are (a) a component of an unassembled article, (b) the total number of nails is sixty (60) or less, and (c) the imported unassembled article falls into one of the following eight groupings: 1) builders' joinery and carpentry of wood that are classifiable as windows, French-windows and their frames; 2) builders' joinery and carpentry of wood that are classifiable as doors and their frames and thresholds; 3) swivel seats with variable height adjustment; 4) seats that are convertible into beds (with the exception of those classifiable as garden seats or camping equipment); 5) seats of cane, osier, bamboo or similar materials; 6) other seats with wooden frames (with the exception of seats of a kind used for aircraft or motor vehicles); 7) furniture (other than seats) of wood (with the exception of i) medical, surgical, dental or veterinary furniture; and ii) barbers' chairs and similar chairs, having rotating as well as both reclining and elevating movements); or 8) furniture (other than seats) of materials other than wood, metal, or plastics (e.g., furniture of cane, osier, bamboo or similar materials). The aforementioned imported unassembled articles are currently classified under the following Harmonized Tariff Schedule of the United States (HTSUS) subheadings: 4418.10, 4418.20, 9401.30, 9401.40, 9401.51, 9401.59, 9401.61, 9401.69, 9403.30, 9403.40, 9403.50, 9403.60, 9403.81 or 9403.89. Also excluded from the scope of this investigation are steel nails that meet the specifications of Type I, Style 20 nails as identified in Tables 29 through 33 of ASTM Standard F1667 (2013 revision). Also excluded from the scope of this investigation are nails suitable for use in powder-actuated hand tools, whether or not threaded, which are currently classified under HTSUS subheadings 7317.00.20.00 and 7317.00.30.00. Also excluded from the scope of this investigation are nails having a case hardness greater than or equal to 50 on the Rockwell Hardness C scale (HRC), a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point, suitable for use in gas-actuated hand tools. Also excluded from the scope of this investigation are corrugated nails. A corrugated nail is made up of a small strip of corrugated steel with sharp points on one side. Also excluded from the scope of this investigation are thumb tacks, which are currently classified under HTSUS subheading 7317.00.10.00. Certain steel nails subject to this investigation are currently classified under HTSUS subheadings 7317.00.55.02, 7317.00.55.03, 7317.00.55.05, 7317.00.55.07, 7317.00.55.08, 7317.00.55.11, 7317.00.55.18, 7317.00.55.19, 7317.00.55.20, 7317.00.55.30, 7317.00.55.40, 7317.00.55.50, 7317.00.55.60, 7317.00.55.70, 7317.00.55.80, 7317.00.55.90, 7317.00.65.30, 7317.00.65.60 and 7317.00.75.00. Certain steel nails subject to this investigation also may be classified under HTSUS subheading 8206.00.00.00 or other HTSUS subheadings. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive. Footnote 1: The shaft length of certain steel nails with flat heads or parallel shoulders under the head shall be measured from under the head or shoulder to the tip of the point. The shaft length of all other certain steel nails shall be measured overall. 3. This investigation has been assigned investigation number A-557-816. 4. For imports of certain steel nails from Malaysia, CBP shall continue to suspend liquidation of such shipments entered, or withdrawn from warehouse, for consumption on or after 05/20/2015. Effective 05/20/2015, CBP shall require, for such entries, a cash deposit equal to the margins for the producers and/or exporters listed below: Producer and/or Exporter: Inmax Sdn. Bhd. Case number: A-557-816-001 Cash deposit rate: 39.35% Producer and/or Exporter: Region International Co. Ltd. and Region System Sdn. Bhd. Case number: A-557-816-002 Cash deposit rate: 2.61% Producer and/or Exporter: Tag Fasteners Sdn. Bhd. Case number: A-557-816-003 Cash deposit rate: 39.35% All Others Case Number: A-557-816-000 Cash Deposit Rate: 2.61% 5. If any entries of this merchandise are exported by a firm other than the producer, then the following instructions apply: A. If the exporter of the subject merchandise does not have its own rate but the producer has its own rate, the cash deposit will be the producer's rate. B. Where neither the exporter nor the producer currently has its own rate or the producer is unknown, use the all-others rate of 2.61 percent to establish the cash deposit. 6. If there are any questions by the importing public regarding this message, please contact the Call Center for the Office of AD/CVD Operations, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce at (202) 482-0984. CBP ports should submit their inquiries through authorized CBP channels only. (This message was generated by OVI:SB.) 7. There are no restrictions on the release of this information. Michael B. Walsh

Frequently asked questions

What is CSMS 5140301?

CSMS 5140301 is a U.S. Customs and Border Protection (CBP) Cargo Systems Messaging Service bulletin titled "Notice of final determination in the antidumping duty investigation of Certain Steel Nails from Malaysia (A-557-816)". CSMS bulletins are the operational instructions CBP issues to brokers, importers, and ACE filers covering rate changes, system updates, scope guidance, and other day-to-day customs-operations changes.

When was CSMS 5140301 published?

CBP published CSMS 5140301 on May 20, 2015. The bulletin's instructions are typically operative as of the publication date unless the body specifies a different effective date.

Which AD/CVD cases does CSMS 5140301 affect?

CSMS 5140301 references 1 AD/CVD case (A-557-816). The links on this page take you to each linked order with its current scope, rates, and history.

Is the CBP CSMS the legally binding instruction?

Learn more

Tandom guides relevant to CBP CSMS messages

Trade compliance APIs in broker workflows

Where trade compliance APIs fit in a broker's filing pipeline: HTS classification, duty calculation, AD/CVD scope match, and post-summary corrections.

Open resource

Find the right manufacturer or exporter rate in an AD/CVD order

Cash deposit cascade, separate rates, all-others, and PRC-wide rates. Worked example on case A-570-910 (galvanized welded steel pipe from China) with three exporter-specific rates.