CSMS 4178305·Trade policy·June 27, 2014·View on csms.cbp.gov ↗

Initiation of antidumping duty investigation of certain steel nails from the Sultanate of Oman (A-523-808)

Plain-English explanation

CSMS 4178305 is a U.S. Customs and Border Protection (CBP) Cargo Systems Messaging Service bulletin (trade policy), published on June 27, 2014. It carries the official CBP guidance brokers and importers must follow for the topic — "Initiation of antidumping duty investigation of certain steel nails from the Sultanate of Oman (A-523-808)". It links to 1 AD/CVD case in Tandom's catalog. CSMS messages are the operational layer between Commerce determinations and at-the-border collections: when Commerce publishes a new rate, scope ruling, or instruction, CBP turns it into a CSMS that ACE/ACS systems and brokers act on.

Linked AD/CVD cases(1)

Cases referenced or affected by this CSMS message

A-523-808

Message body

Full text as published by U.S. Customs and Border Protection

1. On 06/25/2014, Commerce published in the Federal Register its initiation of the antidumping duty investigation of certain steel nails from the Sultanate of Oman (79 FR 36019). 2. The merchandise covered by this investigation is certain steel nails having a nominal shaft length not exceeding 12 inches. (See Footnote 1). Certain steel nails include, but are not limited to, nails made from round wire and nails that are cut from flat-rolled steel. Certain steel nails may be of one piece construction or constructed of two or more pieces. Certain steel nails may be produced from any type of steel, and may have any type of surface finish, head type, shank, point type and shaft diameter. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, including but not limited to electroplating or hot dipping one or more times), phosphate, cement, and paint. Certain steel nails may have one or more surface finishes. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk, and sinker. Shank styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted. Screw-threaded nails subject to this proceeding are driven using direct force and not by turning the nail using a tool that engages with the head. Point styles include, but are not limited to, diamond, needle, chisel and blunt or no point. Certain steel nails may be sold in bulk, or they may be collated in any manner using any material. If packaged in combination with one or more non-subject articles, certain steel nails remain subject merchandise if the total number of nails of all types, in aggregate regardless of size, is equal to or greater than 25. Excluded from the scope of this investigation are certain steel nails packaged in combination with one or more non-subject articles, if the total number of nails of all types, in aggregate regardless of size, is less than 25. Also excluded from the scope of this investigation are steel nails that meet the specifications of Type I, Style 20 nails as identified in Tables 29 through 33 of ASTM Standard F1667 (2013 revision). Also excluded from the scope of this investigation are nails suitable for use in powder-actuated hand tools, whether or not threaded, which are currently classified under Harmonized Tariff Schedule of the United States (HTSUS) subheadings 7317.00.20.00 and 7317.00.30.00. Also excluded from the scope of this investigation are nails having a case hardness greater than or equal to 50 on the Rockwell Hardness C scale (HRC), a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point, suitable for use in gas-actuated hand tools. Also excluded from the scope of this investigation are corrugated nails. A corrugated nail is made up of a small strip of corrugated steel with sharp points on one side. Also excluded from the scope of this investigation are thumb tacks, which are currently classified under HTSUS 7317.00.10.00. Certain steel nails subject to this investigation are currently classified under HTSUS subheadings 7317.00.55.02, 7317.00.55.03, 7317.00.55.05, 7317.00.55.07, 7317.00.55.08, 7317.00.55.11, 7317.00.55.18, 7317.00.55.19, 7317.00.55.20, 7317.00.55.30, 7317.00.55.40, 7317.00.55.50, 7317.00.55.60, 7317.00.55.70, 7317.00.55.80, 7317.00.55.90, 7317.00.65.30, 7317.00.65.60 and 7317.00.75.00. Certain steel nails subject to this investigation also may be classified under HTSUS subheading 8206.00.00.00. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive. Footnote 1: The shaft length of certain steel nails with flat heads or parallel shoulders under the head shall be measured from under the head or shoulder to the tip of the point. The shaft length of all other certain steel nails shall be measured overall. 3. This investigation has been assigned investigation number A-523-808. 4. If there are any questions by the importing public regarding this message, please contact the Call Center for the Office of AD/CVD Operations, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce at (202) 482-0984. CBP ports should submit their inquiries through authorized CBP channels only. (This message was generated by OIV:TT) 5. There are no restrictions on the release of this information. Michael B. Walsh

Frequently asked questions

What is CSMS 4178305?

CSMS 4178305 is a U.S. Customs and Border Protection (CBP) Cargo Systems Messaging Service bulletin titled "Initiation of antidumping duty investigation of certain steel nails from the Sultanate of Oman (A-523-808)". CSMS bulletins are the operational instructions CBP issues to brokers, importers, and ACE filers covering rate changes, system updates, scope guidance, and other day-to-day customs-operations changes.

When was CSMS 4178305 published?

CBP published CSMS 4178305 on June 27, 2014. The bulletin's instructions are typically operative as of the publication date unless the body specifies a different effective date.

Which AD/CVD cases does CSMS 4178305 affect?

CSMS 4178305 references 1 AD/CVD case (A-523-808). The links on this page take you to each linked order with its current scope, rates, and history.

Is the CBP CSMS the legally binding instruction?

Learn more

Tandom guides relevant to CBP CSMS messages

Trade compliance APIs in broker workflows

Where trade compliance APIs fit in a broker's filing pipeline: HTS classification, duty calculation, AD/CVD scope match, and post-summary corrections.

Open resource

Find the right manufacturer or exporter rate in an AD/CVD order

Cash deposit cascade, separate rates, all-others, and PRC-wide rates. Worked example on case A-570-910 (galvanized welded steel pipe from China) with three exporter-specific rates.